Leo4Allv3 Post-installation Discussion

Re: Leo4Allv3 Post-installation Discussion

Tue, 24 Jun 2008 10:33:16 +0000

@1 the only way to get online is bluetooth modem. i just connected USB-Bluetooth and Nokia E51, it's work as far as your handset internet setting is correct. Yes, it is any cost. Because, Atheros Wifi loaded unsuccessfully.

@2 from Knoppix booting, I got that our chipset is known as Realtek ALC 862. But, I haven't seen the driver for it yet.

neva' give up, guys.

Danny64X2 - Indonesia

Re: Leo4Allv3 Post-installation Discussion

Tue, 10 Jun 2008 12:28:06 +0000

Wait, I almost forgot the most important problem. Even though I picked "ForceDeth-V" in the installation disk, and it recognizes my ethernet card, when I plug the cable modem to my laptop, I don't have Internet access. On "Self-Assigned IP" I'm getting:

IP Address: 169.254.130.164
Subnet Mask: 255.255.0.0

I tried using a manual ip settings, but didn't work.

Any help? Please.

Re: Leo4Allv3 Post-installation Discussion

Mon, 09 Jun 2008 14:11:18 +0000

Problem solved! The problem was the chipset kext that I chose on the installation disk. The one that works with my laptop is "NForce Test". Now, I can dual boot between Windows XP SP3 and Leo4Allv3.

The only thing missing on the Leo partition, which I don't see any support in this website or any other, is my graphics card. It's an NVIDIA GeForce Go 7200, Vendor: 0x10de, Device ID: 0x01d6, Revision ID: 0x00a1.

Other than that, everything works just fine!

Thanx for all the help!

Re: Leo4Allv3 Post-installation Discussion

Mon, 09 Jun 2008 10:33:38 +0000

Hi,

I've successfully installed Leo3Allv3 on a T43 but when I reboot after installation is complete i get stuck with "HFS+ partition error".
During installation I "formatted" the partition as extended (journaled) using disk utility.

I booted on the DVD again and corrected file permissions on that partition but still same error when booting.

Anyone with a tip to a MAC newbie?

/Myamoto

Re: Leo4Allv3 Post-installation Discussion

Fri, 06 Jun 2008 04:27:31 +0000

I had the same problem on my GX270 and upgraded the CPU to a version that supports SSE3. Make sure you upgrade your bios from Dell to their latest rev to support the newer CPU types. The installer now completes.

Re: Leo4Allv3 Post-installation Discussion

Wed, 04 Jun 2008 22:40:57 +0000

I have done so much research to see what the best install would be and I believe it is Leo2All. I really hate to ask but is there anybody out there that can give me an invite to the Debonoid.com web site? According to the OS86 forums, It sounds like the most reliable. I have the original OSx Leapord DVD but there are other things I'm sure I will need. Thanks so very much if your out there and can help!
Tana

Re: Leo4Allv3 Post-installation Discussion

Wed, 04 Jun 2008 13:26:52 +0000

Ok, so I fixed the problem with the Boot.plist and also fixed the Permissions using the install disk. Now, when I press Enter on the Leo4Allv3 partition, to boot Leopard, I'm getting various error, like these for example:

disk0s2: I/O error

localhost rpc.statd[47]: can't open statd.notify pidfile: Invalid argument (22)

matching service count = 1

localhost kextd[10]: failed to open kernel link data file (/var/run/mach.sym) - Invalid argument

Any ideas?

Thanx in advanced, Leo4AllNoob

Re: Leo4Allv3 Post-installation Discussion

Sat, 31 May 2008 17:09:26 +0000

Hi,
I am currently getting stuck at

Please help me resolve this problem!
Thanks very much!!

Re: Leo4Allv3 Post-installation Discussion

Fri, 30 May 2008 16:32:34 +0000

I'm using a 128MB AGP GeForce 6600 GT, and I finally got different resolutions to work on my display, but am still trying to get QE to work. How I got the resolutions enabled:

I installed with Leo4allv3 using NVinject 128 ver 0.2.0 and then replaced the resulting NVinject.kext with one I got from a Kalyway 10.5.2 install where I'd selected NVinject-128. I also copied over from that same Kalyway install these two kexts that weren't already in the Leo4allv3 install: NVDANV40Hal.kext and NVDAResman.kext.

I then, of course, did the following to all 3 kexts:

sudo chmod -R 755
sudo chown -R root:wheel

and then:

sudo rm -R /System/Library/Extensions.mkext

I'll update if I can get QE to work.

Re: Leo4Allv3 Post-installation Discussion

Thu, 29 May 2008 18:11:15 +0000

Hi, after a successful install of Leo4Allv3 on my HP DV6040US, on the Darwin Bootloader I can see the two partitions, Windows XP and Leo4Allv3, and I can see that Leo4Allv3 is set to boot primarily since is already highlighted. But as soon as I press Enter on the Leo partition, I gives me the "…/com.apple.Boot.plist cannot be found" error.

Any help will be greatly appreciated :)

Specs:
Product Name: HP DV6040US
Microprocessor: 1.6 GHz AMD Turion™ 64 X2 Mobile Technology TL-52
Memory: 1536MB 667MHz DDR2 System Memory
Video Graphics: NVIDIA GeForce Go 7200
Hard Drive: 120GB 5400RPM SATA - Fujitsu MHV2120BH PL
Multimedia Drive: HL-DT-ST DVDRAM GSA-4084N
Network Card: NVIDIA Network Controller Gigabit Ethernet LAN
Wireless Connectivity: Broadcom 802.11b/g WLAN
Sound: Conexant HD Audio

Re: Leo4Allv3 Post-installation Discussion

Thu, 29 May 2008 15:50:50 +0000

—

Re: Leo4Allv3 Post-installation Discussion

Thu, 29 May 2008 15:19:56 +0000

Ok I have installed the OS. But it keeps churning at
Still waiting for root device

Any ideas on how to surpass this?
My drive is a SATA

Re: Leo4Allv3 Post-installation Discussion

Thu, 29 May 2008 15:14:57 +0000

i have an Intel D945 GNT motherboard with a Pentium D 3 ghz processor, 4 gig ram, DVD drive on IDE master, 120 gig HD on IDE slave, x1900gt 256, and a network card. (all work fine using Leo4allv2 with some customization for the x1900gt)

Leo4allv2 works on this machine without booting problems.

Leo4allv3 DOES NOT… I get "waiting for root device" upon restart over and over and over…

I have used this motherboard since the beginning of the OSX86 project so it is not a question of whether OS X 86 will operate on this board.

Somehow Leo4allv3 is broken…

If I could fix this I would, but my computer expertise only goes so far.

Re: Leo4Allv3 Post-installation Discussion

Thu, 29 May 2008 15:04:39 +0000

—-

Re: Leo4Allv3 Post-installation Discussion

Thu, 29 May 2008 14:57:40 +0000

—-see revised message

Re: Leo4Allv3 Post-installation Discussion

Sat, 24 May 2008 12:33:43 +0000

Yeah I was afraid that would be the answer….

Are there any plans for a x64 amd release?

Thanks
UloPe

Re: Leo4Allv3 Post-installation Discussion

Sat, 24 May 2008 01:12:40 +0000

The best thing you can do is wait for a 64-bit version to come out in the future. Nothing can be done at the moment. Every release is solely made for x86 instructions, that's why. You can disregard the Java update for now. =)

Re: Leo4Allv3 Post-installation Discussion

Fri, 23 May 2008 22:17:35 +0000

Hi,

first of all: Thanks for this awesome distibution :)

System:
AMD Athlon 64 X2 4200+
MSI K9n Neo v2 (nForce 520, Net: Realtek 8111/8168B, Sound: ALC888)
GeForce 8500GT

Leo4allv3
Kernel: Darwin xxxxx.xxxxx.xxx 9.2.2 Darwin Kernel Version 9.2.2: Tue Mar 4 21:17:34 PST 2008; root:xnu-1228.4.31~1/RELEASE_I386 i386

Everything is working nicely except 64bit support.

sysctl:
hw.optional.x86_64: 0
hw.cpu64bit_capable: 0

This is BAD(tm) since i need Java 6 (which is only available in a 64-bit version)

Is there something to be done?

Thanks.
UloPe

Re: Leo4Allv3 Post-installation Discussion

Wed, 21 May 2008 02:05:30 +0000

I use the PS2 adapter but it didn't help :( Keyboard & Mouse setting still absent

Re: Leo4Allv3 Post-installation Discussion

Tue, 20 May 2008 19:34:58 +0000

Hi, thanks for your release but I have a some trouble:
I have the Microsoft Digital Media Pro keyboard and the Microsoft Habu mouse (yep I know it's not the best devices for Mac :) ) when the installation reach the keyboard detecting step it's write "Can't detect the keyboard" then I press OK but when I log in and go to the System Preferences Keyboard & Mouse setting is MISSING :(

Yes, my keyboard and mouse work but I can't use ANY hot keys on keyboard it's not working :( and I don't know where I can adjust it.
Mouse also work too weird, it's very slow.

I found screenshots at Google, I told about this :) :